擺式雷蒙磨粉機在使用過程當中，應有固定人員負責看管，操作人員必須具備一定的技術水平。雷蒙磨在安裝前對操作人員必須進行必要的技術培訓，使之了解雷蒙磨粉機的原理性能，熟悉操作規程，不只是擺式雷蒙磨粉機需要這樣，所有粉體設備在使用中都適用；為使擺式雷蒙磨粉機正常，應制定設備“擺式雷蒙磨粉機設備保養安全操作制度”方能保證磨機長期安全運行，同時要有必要的檢修工具以及潤滑脂和相應的配件。擺式雷蒙磨粉機/擺式磨要根據實際情況制定一個安全檢查檢修的周期，這樣才可以確保億博擺式雷蒙磨粉機生產安全，生產質量同時也可延長機器的壽命；擺式雷蒙磨粉機使用一段時間后，應進行檢修，同時對磨輥磨環鏟刀等易損件進行檢修更換處理，磨輥裝置在使用前后對連接螺栓螺母應進行仔細檢查，看是否有松動現象，潤滑油脂是否加足；擺式雷蒙磨粉機裝置使用時間超過500小時左右重新更換磨輥時，對輥套內的各滾動軸承必須進行清洗，對損壞件應及時更換，加油工具可用手動加油泵和黃油槍。