雷蒙磨粉機的使用與保養 1、 磨粉機在使用過程當中，應有固定人員負責看管，操作人員必須具備一定的技術水平。磨粉機在安裝前對操作人員必須進行必要的技術培訓，使之了解磨粉機的原理性能，熟悉操作規程。 2、 為使磨機正常，應制定設備“設備保養安全操作制度”方能保證磨機長期安全運行，同時要有必要的檢修工具以及潤滑脂和相應的配件。 3、 磨機使用一段時間后，應進行檢修，同時對磨輥磨環鏟刀等易損件進行檢修更換處理，磨輥裝置在使用前后對連接螺栓螺母應進行仔細檢查，看是否有松動現象，潤滑油脂是否加足。 4、 磨輥裝置使用時間超過500小時左右重新更換磨輥時，對輥套內的各滾動軸承必須進行清洗，對損壞件應及時更換，加油工具可用手動加油泵和黃油槍。 5、 細度調節，根據物料的大小、軟硬、含水量、比重不同，加工的粗細度也不同，可調節上方的分析器，轉速高、細度高，轉速低、細度低。提高細度，產量會相應降低，如果還達不到要求時應調試風機轉速，用戶可靈活掌握。 6、磨輥磨環的報廢極限，剩余小壁厚不得小于10mm. 7、停車時，先停止進料，主機仍繼續盍，使殘留的磨料繼續進行碾磨，約一分鐘后，可關閉主機電動機和分析器電機，停止碾磨工作，其后再停止風機電動機，以便吹凈殘留的粉末。